ULTRAFAST PULSED LASER INDUCED LIFT-OFF PATTERNING OF CZTSE THIN-FILM SOLAR CELLS

Edgaras Markauskas1

1 Center for Physical Sciences and Technology, Savanoriu ave. 231, LT-02300, Vilnius, Lithuania

Rapidly growing thin-film photovoltaic market is driven by two polycrystalline technologies: CdTe and CuInxGa1-xSe2 (CIGS) due to relatively high performance for converting sunlight into electricity and low module costs. On the other hand, converging to terawat-scale deployment, these absorbers have some limitations due to scarcity of indium, gallium and tellurium [1, 2]. In Cu2ZnSnSe4 (CZTSe) absorber these rear elements can be replaced by cheaper and more earth abundant elements such as Zn and Sn, therefore this type of thin-film solar cells have drawn a lot of attention as a perspective material for CIGS technology replacement.

Kesterite (CZTSe) technology shows efficiencies up to 12.6% for small scale devices [3]. However, after the transition from small scale to full-sized solar modules, high photocurrent and resistance losses are introduced. In order to preserve efficiency of small solar cells, large solar panel is divided into smaller adjacent cells which afterwards are interconnected in series by three patterning processes. These processes are integrated in roll-to-roll production of thin-film solar cells. Recent investigations revieled formation of melted area and degradation of the devices electrical properties even after irradiation of ultrashort laser pulses [4].

For this reason we proposed laser induced material lift-off process for the front side scribing of the CZTSe solar cells. Using proper laser wavelength, it is possible to control laser energy coupling in the complex film layer structure. High absorption at inner interface of the layers triggers localized rapid temperature rise which facilitates localized spallation of the films rather than evaporation. This material lift-off process enables to process thermally sensitive films as all the laser affected material is mechanically removed from the laser ablation area [5].

Ablation and scribing experiments were carried out with fundamental harmonics of the picosecond laser (Atlantic, 1064 nm, 10 ps, from EKSPLA) and tunable pulse duration femtosecond Yb:KGW laser (Pharos, 1030 nm, 300 fs, from Light Conversion).

In our recent investigations, we have studied influence of the laser pulse length to a laser-induced material lift-off process for the front-side scribing of the CZTSe solar cells. Laser pulse duration was changed between 300 fs, 1 ps and 10 ps durations. Two types of multilayer structure of the CTZSe solar cells were investigated: : (i) complete structure consisting of TCO top-contact, Cu2ZnSnSe4 absorber layer, molybdenum back-contact and soda-lime-glass as a substrate and (ii) incomplete CZTS/Mo/SLG structure without top-contact.

Single pulse ablation and scribing experiments were performed on thin-film CZTSe structure in order to find optimal conditions for the Mo back-contact exposure in both P2 and P3 processes. It was determined that at specific experimental conditions, constant and high repeatability lift-off craters could be formed in CZTSe thin-film solar cell structures. SEM images, EDX and Raman spectrums were investigated in order to compare laser pulse length influence to lift-off effect.


[1] N. Vora, J. Blackburn, I. Repins, et al., Phase identification and control of thin films deposited by co-evaporation of elemental Cu, Zn, Sn, and Se, Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, vol. 30, (2012).

[2] H. Katagiri, K. Jimbo, et al., Development of CZTS-based thin film solar cells, Thin Solid Films 517, 2455-2460, (2009).

[3] W. Wang, M. T. Winkler, O. Gunawan, et al., Device Characteristics of CZTSe Thin-Film Solar Cells with 12.6% Efficiency, Advanced Energy Materials, (2013).

[4] P. Gečys, G. Račiukaitis, A. Wehrmann, et al., Scribing of Thin-Film Solar Cells with Picosecond and Femtosecond Lasers, Journal of Laser Micro / Nanoengineering, vol. 7, p. 33, (2012).

[5] G. Račiukaitis, S. Grubinskas, et al., Selectiveness of laser processing due to energy coupling localization: case of thin film solar cell scribing, Applied Physics A: Materials Science & Processing, 1-6, (2012).