COMPARISSON OF PHASE COMPOSITION OF TiO2-M0O3 NANOCOMPOSITE SYSTEMS SYNTHESIZED BY DIFFERENT METHODS

Natalia Boboriko1

1 Department of Chemistry, Belarusian State University, Minsk, Belarus

Multioxide TiO2-MoO3 systems with different oxide molar ratio find industrial application as catalysts of dehydration, oxidation, ammoxidation et al. These systems also can be used as gas sensing layers of solid state chemical sensors. Our earlier investigations [1] showed the availability of using TiO2-M0O3 multioxide systems as gas sensing materials for hydrogen detection. It is widely known, that gas sensing properties of multioxide materials depend on their phase composition. This work is dedicated to the comparison of crystalline phase composition of TiO2-MoO3 systems, synthesized by three different ways. The first one is traditionally used penetration method, where TiO2 powder is impregnated by water solution of ammonium molybdate with subsequent drying and thermal treatment. The second one is colloid-chemical method of synthesis. Colloid-chemical synthesis allows obtaining multioxide materials with developed surface and high level of homogeneity at molecular level, with modified phase composition and controllable structural peculiarities. All this makes it possible to influence physical macroscopic properties of synthesized material, which are dependent on surface and structural features, by the change of synthesis parameters such as the nature of precursors, rate of stirring, pH level and heat treatment conditions. And the third synthetic way is synthesis of TiO2-MoO3 system by mixing of individual powders of TiO2 and MoO3 in quantitative ratio with subsequent thermal treatment.

To prepare samples by penetration method pure TiO2 powder was used (it was synthesized by drying of TiO2.nH2O sol and its subsequent annealing at 850 °C for 2 hours). Precise amount of TiO2 powder was drowned into ammonium paramolybdate aqueous-ammonia solution, dried thereafter at 80 °C and annealed at 450 and 850 °C. Ammount of ammonium paramolybdate solution varied to obtain multioxide systems with 1, 5 and 10 mol.%. Colloid-chemical synthesis of TiO2-M0O3 multioxide materials comprised obtaining of TiO2.nH2O sol on the basis of TiCl4 solution in hydrochloric acid and subsequent modification of the obtained sol with calculated amount of ammonium paramolybdate to obtain initial sols for TiO2-MoO3 system formation with MoO3 content of 1, 5 and 10 mol.%. After heating titanium hydrated oxide TiO2.nH2O and ammonium paramolybdate (NH4)6Mo7O24 decomposed to produce TiO2 and MoO3 correspondingly. After drying samples were heated at 450, 600 and 850 °C. The third set of samples was prepared by mixing of TiO2 and MoO3 powders with subsequent heating at 450 and 850 °C.

To investigate phase composition of synthesized materials XRD analysis was used. It was established, that phase composition of samples, synthesized by colloid-chemical method depends both on quantitative component ratio in multioxide systems and on the annealing temperature. Addition of molybdenum trioxide to titanium dioxide shifts anatase-rutile transformation to high temperature region. For TiO2-MoO3 samples annealed at 450 °C and 600 °C crystallographic phase of rutile was not registered, while for pure TiO2, annealed at this temperature, both phases of anatase and rutile were present. Formation of $\alpha$-MoO3 crystal phase is observed after heating samples with 5 and 10 mol.% of MoO3 at 600 °C. For sample with 1 mol. % of MoO3 masking of $\alpha$-MoO3 phase is distinctive. Annealing at 850 °C leads to the formation of rutile phase only and destruction of crystallographic phase of $\alpha$-MoO3 for all samples.

Samples synthesized by mixing of individual powders of TiO2 and MoO3 are characterized by the presence of rutile, anatase and $\alpha$-MoO3 crystalline phases after drying at 80 °C and annealing at 450 and 600 °C. Heat treatment at 850 °C leads to the formation of rutile crystalline phase only.

Synthesis by penetration method leads to the formation of rutile crystal phase after heating at 450 °C, rutile and $\alpha$-MoO3 crystal phases after heating at 600 °C and rutile phase after heat treatment at 850 °C.

Thereby the best way to synthesize TiO2-MoO3 multioxide system with different oxide ratio for gas sensing applications is colloid-chemical method, as this method allows controlling of phase composition of the material by the quantity of MoO3 in the system and by the value of the annealing temperature. Use of this method makes it possible to preserve TiO2 in anatase crystal phase, which is important for practical applications.


[1] D.I. Mychko, N.E. Boboriko, G.F. Karkotsky, N.S. Dashko Influence of doping materials on titanium dioxide gas sensing properties / Sviridov Readings – 2012. Abstract book. Minsk. 2012. P. 27.