VOLUMETRIC DAMAGEABILITY OF TIRE–ASPHALT CONTACT PAIR UNDER VARIOUS LOADS

Gleb Gribovskii1

1 Department of Theoretical and Applied Mechanics, Belarusian State University, Belarus

Computer models for describing the three-dimensional stress-strain state of a system tire-asphalt are of great practical importance for determination assessment of volume damageability and wear of the tire tread and the asphalt pavement, which work in conditions of contact, mechanical and sliding fatigue. Today, there are many works dedicated to analytical and computer simulation of stress-strain state of the “rim-tire-asphalt" separate system components [1,2].

The main goal of this work is to use finite-element modeling for the analysis of simultaneous contact interactions of the full multielement system "rim-tire-asphalt" [3], loaded by the various inner pressure PS (from 0.65 to 0.85 MPa, $\Delta p$=0.5 MPa) and radial load FH (from 6 to 10 kN, $\Delta f$=1 kN) on rim, 3D stress-strain state and the state of volumetric damageability. Truck tire geometric model of 22.5" radius with a simplified rim was taken for the calculation in ANSYS. The following components were added to the model [4] of tire: steel belts, radial ply, wire bead, rubber tread.

Calculation of damageability is based on the model of deformable solid mechanics with dangerous volume. According to this model dangerous volume is the volume where acting stresses are greater than limiting stress [5].

Figure 1
Fig. 1. (a) Model of the system with scheme of loads. (b) Minimum (by PS = 0.65 MPa, FH = 6 kN) and (c) maximum (by PS = 0.85 MPa, FH = 10 kN) dangerous volume. (d) 3D plot of dangerous volumes values Vint by all loads in contact zone: top surface – tire tread; bottom surface – asphalt pavement

Volume damageability by stress intensity (${\sigma_{int}^{(lim)} = 0.5}$ MPa) of tire and asphalt in the contact zone under various loads were calculated (fig. 1-b, 1-c, 1-d). When the radial load on the rim is increased from 6 to 10 kN dangerous volumes in asphalt is also increased 6-7.5 times and in rubber thread increased 2.5-3 times in contact area. If inner pressure is increased from 0.65 to 0.85 MPa than dangerous volumes in tire and asphalt are increased slightly. Minimal value of dangerous volume in asphalt is 2623 mm3 and in tire is 13883 mm3 (fig. 1-b). Maximum value of dangerous volume in asphalt is 20722 mm3 and in tire is 42950 mm3 (fig. 1-c).


[1] Imad L. Al-Qadi, Hao Wang, Prediction of tire pavement contact stresses and analysis of asphalt pavement responses: a decoupled approach, Journal of the Association of Asphalt Paving Technologists 80, 289-316 (2011).

[2] S. L. Sokolov, Experimental and computational analysis of stress-strain state of pneumatics in breaker zone under mechanical effects, Journal of Machinery Manufacture and Reliability 40, 568-572 (2011).

[3] G. V. Gribovskiy, S. S. Sherbakov, Volume damageability of rim-multicomponent tire-asphalt-concrete tribo-fatigue system, International Scientific and Technical Collection Theoretical and Applied Mechanics 32, 277 – 282 (2017).

[4] G. V. Gribovskii, Three-dimensional stress-strain state and volumetric damageability of tire—asphalt contact pair, 60th scientific conference for young students of physics and natural sciences Open Readings 2017, Vilnius University, 73 (2017).

[5] L. A. Sosnovskiy, TRIBO-FATIGUE: Wear-Fatigue Damage and its Prediction (Springer-Verlag, Berlin, Heidelberg, 2005)