A POSSIBILITY TO REDUCE SPHERICAL THERMAL ABERRATIONS IN DIODE PUMPED SOLID-STATE LASERS

Dominykas Bričkus1, 2, Alexander S. Dement'ev1

1 Center for Physical Sciences and Technology, Savanorių av. 231, Vilnius 02300, Lithuania

2 Department of Quantum Electronics, Vilnius University, Saulėtekio av. 9, Vilnius 10222, Lithuania

Thermally induced spherical aberrations in solid state lasers are one of the main issues for high average power scaling possibilities. Therefore, we take a closer look at the possibility to reduce the spherical aberration by the use of certain pump distribution taking into account temperature dependence of the thermal conductivity coefficient $k(T) = a /T$, where $a = k_0 T_r$, and $k_0$ is the coefficient of thermal conductivity at reference temperature $T_r$. We discuss a case of steady-state radial heat flow in cylindrical rods with radially symmetric heating distribution. This allows to simplify the problem enough to obtain simple analytic solutions for various heat load distributions $Q_h(r,z)$ and the following boundary condition $-k(T)(\partial T/\partial r)_{r=R} = h(T-T_a)$, where $R$ is the radius of the rod and $h$ is the convective heat transfer coefficient [1]. A particularly simple solution can be found for the polynomial radial heating distribution

$$Q_{h}(r,z) = Q_{0}(z) \sum_{i=0}^{m} b_{i} \left(\frac{r}{R}\right)^{i}, \ T(r,z) = T(0,z) \exp \left[-\frac{T_{k}(z)}{T_{r}} \sum_{i=0}^{m} \frac{b_{i}}{(i+2)^{2}} \left(\frac{r}{R}\right)^{i+2}\right], \tag{1}$$

where $T_k(z) = Q_0(z)R^2/k_0$. By certain choice of coefficients $b_i$ the particular solutions may be obtained [1,2].

It is important to note that due to non-linear heat conductivity coefficient even uniform heat load distribution will give rise to higher than second order terms in (1). In general, a temperature change in the active medium can modify light beam phase by three different mechanisms: refractive index change due to temperature directly, due to temperature gradient induced strains and stresses and due to end face bulging. Additionally, we have to consider that throughout the long rod the light will be bent by thermal lens, so simply integrating the refractive index along the rod at constant radius will not suffice. We attempt to account for this by modelling the beam with geometric rays which are traced through the active medium and the phase change is calculated over the path of the ray. Thus, using fitting procedure, the optical path difference can be written as $\delta \Lambda(r) = r^2/2\tilde{f}_T - C_a r^4$. This means that the pumped crystal acts as a lens with focal length and has a spherical aberration defined by the coefficient $C_4$. The effect of spherical phase aberration on the beam quality has been analyzed in [3,4]. It was shown that final beam quality with the quartic-aberration can be written as

$$M_f^2 = \sqrt{(M_i^2)^2 + (M_q^2)^2}, M_q^2 = \frac{8\pi\beta_r}{\lambda} C_4 \overline{r^4}, \beta_r = \sqrt{\overline{r^2 r^6} / \overline{r^4}^2} - 1, \tag{2}$$

in which $M_i^2$ is the beam quality factor of the initial unaberrated beam, $M_q^2$ is the additional contribution to the beam quality factor caused by the quartic-phase aberration effects and $\overline{r^2}$, $\overline{r^4}$, and so on are radial moments on the transverse intensity profile. It may be shown that for super-Gaussian beams with intensity profile $I(r) = I_0 \exp[-2(r/w_L)^n]$ intensity moments and coefficient $\beta_r$ for quartic aberration may be expressed as

$$\overline{r^{s}} = W_{L}^{s} \left(\frac{1}{2}\right)^{\frac{s}{n}} \Gamma\left(\frac{s+2}{n}\right) / \Gamma\left(\frac{2}{n}\right), \ s=2,4,6, \ \beta_{r} = \sqrt{\Gamma(4/n)\Gamma(8/n) / \Gamma^{2}(6/n) - 1}, \tag{3}$$

where $\Gamma(z)$ is gamma-function. Beam quality factor has been obtained previously [4] for more general polynomial phase aberration $\Phi_L(r) = \alpha_m (r/w_L)^m$. For super-Gaussian beams with $n=4$ and $n=6$ the initial beam quality factors are $M_i^2 = 2/\sqrt{\pi} \approx 1.13$ and $M_i^2 \approx 1.30$ respectively. Thus, using formulae (2) and (3), the beam propagation coefficient may be calculated not only for Gaussian beam with quartic phase aberration, but also for super-Gaussian beams. For spherical aberration the beam propagation coefficient increases strongly with increasing width of probe beam. However, it can be shown that for certain combination of $b_i$ coefficients in the pump beam the fourth order aberration term could be completely removed taken into account the temperature dependence of the total change of the thermal refractive index due to thermo-optic and photoelastic effects. Thus, the degradation of beam quality will only depend on the higher order aberrations, and therefore will be not so strong.


[1] A.S. Dement'ev, A. Jovaiša, K. Račkaitis, F. Ivanauskas, J. Dabulytė-Bagdonavičienė, Numerical treatment of the temperature distribution in end-pumped composite laser rods, Lithuanian J. Phys., 47, 279-288 (2007).

[2] G.L. Bourdet and C. Gouédard, Simple analytical derivations of thermal lensing in longitudinally Q-CW pumped Yb:YAG, Appl. Opt., 49, 4160-4167 (2010).

[3] W.A. Clarkson, Thermal effects and their mitigation in end-pumped solid-state lasers, J. Phys. D: Appl. Phys., 34, 2381-2395 (2001).

[4] A.S. Dement'ev, A. Jovaiša, G. Šilko, R. Čiegis, On alternative methods for measuring the radius and propagation ratio of axially symmetric laser beams, Quantum Electronics, 35, 1045-1052 (2005).