CHANGES IN MICROBIOTA AND PH VALUES OF CREOSOTE-TREATED WOOD DURING MYCOREMEDIATION

Guoda Kolkatovaitė1, Rūta Mickienė1, Vilma Kaškonienė1, Audrius Sigitas Maruška1

1 Instrumental Analysis Open Access Centre, Faculty of Natural Sciences, Vytautas Magnus University, Lithuania

Creosote oil is a thick liquid obtained by the fractional distillation of crude coal tars. The color of this compound varies from yellow to amber and it was used as the main preservative for wood structures like railway sleepers to protect the wood from microorganisms, fungi, and bacteria [1, 2].

Coal tar contains several hundreds of organic compounds therefore creosote is a mixture of more than 200 organic compounds [2]. Its composition differs depending on origin of coal and manufacturing processes but in general, creosote consists of approximately 85% of polycyclic aromatic hydrocarbons (PAH) and 10% of phenolic compounds [1]. PAH cause negative effects to humans and the environment due to their recalcitrant character and their carcinogenic and mutagenic properties. Therefore, the combustion of creosote-treated wood is allowed only in highly protected plants. This way of handling pollutants is costly and complicated. Potentially, mycoremediation could be a less expensive and more environmentally friendly approach [3]. In order to achieve highly effective bioremediation, it is important to analyze the changes of pH and the total count of microbiota during the biodegradation [1]. To our knowledge, there are no studies related to PAH biodegradation using white-rot fungi by optimizing pH and the total count of microbiota of the media.

This study was performed in the transparent buckets using white-rot fungus, namely Pleurotus ostreatus, Pleurotus eryngii and Irpex lacteus. Creosote-treated wood was chopped into smaller pieces (6.0±0.1) cm. Wheat straw was sterilized in order to prevent the contamination of inoculant in early growth stage. Creosote-treated wood, wheat straw and inoculant were layered in 3 different ways in order to analyze samples obtained under different conditions. Initial pH of wood was 4.97. On the 60th day of the experiment, the highest 7.01 pH was reached with P. ostreatus inoculum pH 6.92 was measured with I. lacteus inoculum, and pH 6.83 with P. eryngii. The smallest pH value was observed in control sample, where pH 5.4 was obtained.

The total count of bacteria and the total count of yeasts and molds together were determined using commercial selective Compact DryTM media for bacteria (TC), and for yeasts and molds (YM). In the beginning of experiment, 5.1·103 CFU/ml of bacteria and 2.3·103 CFU/ml of yeasts and molds together were calculated in the samples. Total count of microbiota increased after biodegradation. Samples with P. ostreatus inoculum contained the highest amount of microorganisms (2.4·104 CFU/ml bacteria, 6.1·103 CFU/ml yeasts and molds), while the lowest values were observed in samples with Irpex lacteus inoculum (1.9·104 CFU/ml bacteria, 5.2·103 CFU/ml yeast and mold).

White-rot fungi Pleurotus ostreatus, Pleurotus eryngii and Irpex lacteus change pH values in PAH biodegradation process from 4.97 to 7.01 and change total count of microbiota from 7.4·103 CFU/ml to 3.0·104 CFU/ml.

Acknowledgments: The study was financed by the Research Council of Lithuania (project No. 09.3.3-LMT-K-712-25-0195).


[1] JÚLIO, Aline Daniela Lopes, et al. Metataxonomic analyses reveal differences in aquifer bacterial community as a function of creosote contamination and its potential for contaminant remediation, Scientific reports 9.1, 1-14 (2019).

[2] LEE, Hwanhwi, et al. Bioremediation of polycyclic aromatic hydrocarbons in creosote-contaminated soil by Peniophora incarnata KUC8836, Bioremediation Journal 19.1, 1-8 (2015).

[3] POLCARO, C. M., et al. Fungal bioremediation of creosote-treated wood: a laboratory scale study on creosote components degradation by Pleurotus ostreatus mycelium, Bulletin of environmental contamination and toxicology 81.2, 180-184 (2008).