MOLECULAR ENGINEERING OF THE FLUORENE-BASED HOLE TRANSPORTING MATERIALS FOR EFFICIENT PEROVSKITE SOLAR CELLS

Aistė Jegorovė1, Cristina Momblona2, Marytė Daškevičienė1, Artiom Magomedov1, Rimgailė Degutytė3, Abdullah M. Asiri4, Vygintas Jankauskas5, Albertus Adrian Sutanto2, Mohammad Khaja Nazeeruddin2, Vytautas Getautis1

1 Department of Organic Chemistry, Kaunas University of Technology, Lithuania.

2 Group for Molecular Engineering of Functional Material, Institute of Chemical Sciences and Engineering, École Polytechnique Fédérale de Lausanne, Switzerland.

3 Department of Food Science and Technology, Kaunas University of Technology, Lithuania.

4 Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, Saudi Arabia.

5 Institute of Chemical Physics, Vilnius University, Lithuania.

Nowadays, people cannot imagine their life without everyday appliances. Most of these devices require electricity to operate. One of the most popular ways to extract energy is from non-renewable energy sources. But these energy sources have drawbacks, such as its residual products are generally non-biodegradable and can cause damage to environment. Consequently, scientists have been looking for alternative ways to generate energy from renewable sources, such as wind energy, solar energy, hydropower etc. The Sun is known to be the most powerful source of energy. Solar cells are devices that convert absorbed light into electricity and silicon solar cells are currently the most commonly used technology to do that. However, it has its own drawbacks and other high efficiency solar cell technologies have been developed. Perovskite solar cells (PSCs) have recently emerged as a promising technology for the further cost reduction of the energy production from the sunlight. Perovskite solar cells are among the most efficient third-generation cells however, there are several obstacles that need to be addressed for it to see a widespread use. One of them is the use of expensive charge-transporting semiconductors such as Spiro-OMeTAD or fullerene derivatives to obtain efficient devices [1]. Therefore, there is a vigorous search for cheaper and simpler methods for the synthesis of organic semiconductors. According to literature carbazole and fluorene chromophores are among the most popular structural building blocks, used for the construction of organic hole-transporting materials (HTMs) [2–4].

In this work we synthesized Spiro-OMeTAD analogues and simpler “half” structures, containing carbazolyl- and methoxyphenyl-chromophores, that have been obtained by a simple synthetic method. Thermal and photoelectrical properties were investigated and compared with Spiro-OMeTAD.

Molecular engineering of new hole transporting materials was realized under Hartwig-Buchwald amination conditions using commercially available starting materials. New compounds bear alkylated/arylated fluorene and spirobifluorene fragments as molecule-core, while 9-ethyl-N-(4-metoxyphenyl)-9H-carbazol-3-amine and bis(9-ethyl-9H-carbazol-3-yl)amine were used to build side chromophores. All synthesized HTMs exhibit good thermal stability, which depends on alkyl chain length and the number of carbazolyl moieties, at up to 400 °C. Almost all new HTMs showed Tg significantly exceeding 100 °C. According to DSC data the polymerization temperatures can be observed for materials V1241 and V1274. These materials have vinyl group at central moiety. Polymers exhibit much better film-forming ability, than small-molecular organic HTM's and high hydrophobicity [5]. Unfortunately, these materials are not suitable for production of solar cells with an n-i-p structure due to their high polymerization temperatures (above 300 °C). Nevertheless, other compounds have amorphous state, which is important for homogenous films forming. The ionization potential (Ip) of target materials is in range of 4.85–5.28 eV which is suitable for use target materials in perovskite solar cells. From obtained data it is evident that all of materials are suitable for use in perovskite solar cells except for V1241 and V1274. The PCE of the most efficient n-i-p PSCs perovskite device containing carbazolyl-terminated Spiro-OMeTAD analogue V1267 have reached 18.3 %. The devices fabricated using the other HTMs reached lower efficiency: V1269 (18.1 %), V1258 (17.8 %), V1240 (17.6 %), V1257 (17.21 %), V1238 (16.1 %), V1226 (15.7 %), V1222 (15.7 %). Furthermore, “half” structures with methoxyphenyl/carbazolyl fragments show good long-term stability and outperform Spiro-OMeTAD.


[1] T. P. I. Saragi, T.Spehr, A. Siebert, T. Fuhrmann-Lieker, J. Salbeck. Chem. Rev. 107, 1011-1065 (2007).

[2] X. Liu, S. Ma, M. Mateen, P. Shi, C. Liu, Y. Ding, M. Cai, M. Guli, M. K. Nazeeruddin, S. Dai, Sustainable Energy Fuels, 4, 1875 (2020).

[3] D. Y. Lee, G. Sivakumar, Manju, R. Misra, S. I. Seok, ACS Appl. Mater. Interfaces, 12, 28246 (2020).

[4] S. Daskeviciute, C. Momblona, K. Rakstys, A. A. Sutanto, M. Daskeviciene, V. Jankauskas, A. Gruodis, G. Bubniene, V. Getautis, M. K. Nazeeruddin, J. Mater. Chem. A, 9, 301 (2021).

[5] X. Sun, X. Yu, Z. Li. ACS Appl. Energy Mater. 3, 11, 10282–10302 (2020).