Open Readings 2022 • P6-14
TOWARDS ELECTROCHEMICAL POLYMERIZATION OF POLYPYRROLE/POLY(METHYLENE BLUE) LAYER DOPED BY POLYSACCHARIDES
Raimonda Boguzaite1, Vilma Ratautaite1, 2, Ernestas Brazys2, Almira Ramanaviciene3, Arunas Ramanavicius1, 2
1 Department of Functional Materials and Electronics, Center for Physical Sciences and Technology, Sauletekio av. 3, Vilnius LT-10257, Lithuania
2 Department of Physical Chemistry, Institute of Chemistry, Faculty of Chemistry and Geosciences, Vilnius University, Naugarduko str. 24, Vilnius LT-03225, Lithuania
3 NanoTechnas – Center of Nanotechnology and Materials Science, Faculty of Chemistry and Geosciences, Institute of Chemistry, Vilnius University, Naugarduko Str. 24, LT-03225 Vilnius, Lithuania
Polypyrrole (Ppy) and methylene blue are electroactive compounds that can be polymerized by electrochemical polymerization methods [1]. Ppy is one of the most analyzed conducting polymers used for the development of various types of sensors. Meanwhile, methylene blue (MB) is a phenothiazine derivative, which in analytical chemistry is used as a redox mediator that undergoes color changes from bright blue to colorless when the oxidized form becomes reduced. In recent years several studies describing the combination of Ppy and PMB have been published [2,3].
The conductivity of Ppy can be effectively tuned by a careful selection of dopants [4,5]. In most cases, small ions of strong acids are used as dopants, for instance, chloride, sulfate, and others [5,6]. Among the various dopants, saccharides are special substances [4,7].
In this study the aim was to compare the effect of the saccharides (Lactose, Sucrose, and Heparin) on the Ppy-PMB layer. The electrochemical deposition was carried out from a solution containing of 50 mM of pyrrole, 10 mM of methylene blue, and one of the doping materials: 0.1 M Lactose, 0.1 M Sucrose, or 0.01 g/L Heparin. Polymerization was performed at a room temperature during 25 potential cycles in the range from –0.5 V to +1.2 V vs. Ag/AgCl, at the sweep rate of 50 mV/s and step potential of 2.44 mV.
The obtained layers were investigated, and their properties evaluated. The morphology of the layers was analyzed by the AFM method. From these images, it was concluded that the saccharides used in this study have a moderate effect on the surface morphology.
The Ppy-PMB layer doped with heparin was selected for the further experiment and it was applied in the design of electrochromic sensors.
[1] Plausinaitis, D.; Sinkevicius, L.; Samukaite-Bubniene, U.; Ratautaite, V.; Ramanavicius, A. Evaluation of Electrochemical Quartz Crystal Microbalance Based Sensor Modified by Uric Acid-imprinted Polypyrrole. Talanta, 220, 121414 (2020).
[2] Godwin, J.M.; Evitts, R.W.; Kennell, G.F. Microbial fuel cell with a polypyrrole/poly(methylene blue) composite electrode. Rep. Electrochem., 2, 3-11 (2012).
[3] Boguzaite, R.; Ratautaite, V.; Mikoliunaite, L.; Pudzaitis, V.; Ramanaviciene, A.; Ramanavicius, A. Towards analytical application of electrochromic polypyrrole layers modified by phenothiazine derivatives. J. Electroanal. Chem., 886, 115132 (2021).
[4] Serra Moreno, J.; Panero, S.; Materazzi, S.; Martinelli, A.; Sabbieti, M.G.; Agas, D.; Materazzi, G. Polypyrrole-polysaccharide thin films characteristics: Electrosynthesis and biological properties. J. Biomed. Mater. Res. A, 88A, 832-840 (2009).
[5] V. Ratautaite, R. Boguzaite, M.B. Mickeviciute, L. Mikoliunaite, U. Samukaite-Bubniene, A. Ramanavicius, A. Ramanaviciene, Evaluation of Electrochromic Properties of Polypyrrole/Poly(Methylene Blue) Layer Doped by Polysaccharides, Sensors, 22, 232 (2022).
[6] V. Ratautaite, G. Bagdziunas, A. Ramanavicius, A. Ramanaviciene, An Application of Conducting Polymer Polypyrrole for the Design of Electrochromic pH and CO2 Sensors, J. Electrochem. Soc., 166, B297-B303 (2019).
[7] Alizadeh, N.; Tavoli, F. Enhancing electrochromic contrast and redox stability of nanostructure polypyrrole film doped by heparin as polyanion in different solvents. J. Polym. Sci. A Polym. Chem., 52, 3365-3371 (2014).