STARCH-BASED BIODEGRADABLE FILMS BEHAVIOUR AFFECTED BY COLLAGEN DERIVATIVES INCORPORATION

Olena Ishchenko1, Maksym Koliada1, Viktoriia Plavan1

1 Department of Applied Ecology, Technology of Polymers and Chemical Fibers, Kyiv National University of Technologies & Design, Ukraine

Recently, environmentally friendly materials from natural and renewable resources have received much attention. Collagen hydrolysates, which can be obtained from tannery waste, has excellent biodegradability and can be used for biodegradable film formation. While performing composites, except collagen, contain hydrophilic polymers, structural reagents (formaldehyde, glyoxal, glutaraldehyde, tanning agents or minerals), organic fillers (starch, cellulose and chitosan) and plasticizers, such as glycerin. As hydrophilic polymers polyvinyl alcohol, polyethylene glycol/polyethylene oxide, polyvinylpyrrolidone, propylene glycol alginate or a combination thereof can be used. Such combination allows adjusting the properties of the composite materials, including moisture content, viscosity, strength, organoleptic properties and biodegradation ability.

Starch, as an abundant raw material with low cost, has been applied in the field of degradable plastics, and blend films containing starch are potential materials in the agriculture, medicine, and packaging industries [1]. To improve the mechanical properties of materials, blending starch with other polymers such as polymethylcellulose and low-density polyethylene is regarded as the simplest way.

Starch blended with synthetic polymer polyvinyl alcohol (PVA) has been studied as a potential biodegradable polymer [2]. The mechanical properties and biodegradability of starch/PVA blended films have been reported by several researchers. However, their wide applicationsare limited by the lack of water resistance and the poor mechanical property of starch/PVA blended films.

Films were obtained by means of the solvent casting procedure after the preparation of film forming dispersions. Starch (10% w/w) was dispersed in an aqueous solution at 95 °C for 30 min to induce starch gelatinization. PVA 10% solution was prepared by stirring for 40 minutes on a water bath. Afterwards, PVA was incorporated into the starch dispersion, the dispersion was maintained at 90 °C for 30 min under stirring until complete dissolution. Finally, glycerol was added as a plasticising agent. We prepared following ratios 3:1, 1:1 and 1:3 of each of the compositions - PVA/starch; starch/gelatine and dialdehyde starch/gelatine.

The film forming dispersions were poured into glass casting plates (15x10 cm) in the right amount to provide stable surface solid density. The films were dried at 50°C and for 1 h and afterwards, peeled off the casting surface.

In order to find the optimal composition of film-forming dispersion we conducted rheological study of the solutions, water absorption, aqueous solubility and release of starch component as well as physical mechanical properties.

Common corn starch is characterized by a high content of hydroxyl groups, which leads to premature decomposition of the polymer composites. Therefore, modification of starch is required to create a water-insoluble film. Therefore we used starch modified by oxidation, using sodium periodate - dialdehyde starch (DS). This modification allows getting a transparent film, which greatly expands its applications. Depending on the expiration period and operational requirements the optimum ratios are 25:75 and 50:50 dialdehyde starch/gelatin/glycerol for the film formation. Films were resistance to water dissolving.


[1] Xiong, H., Tang, S., Tang, H., & Zou, P. (2008). The structure and properties of a starch-based biodegradable film. Carbohydrate Polymers, 71(2), 263-268.

[2] Xiao, C. M., & Yang, M. L. (2006). Controlled preparation of physical cross-linked starch-g-PVA hydrogel. Carbohydrate Polymers, 64, 37–40.