Passively mode-locked fiber lasers are unsurpassed in terms of the beam quality, operation stability, compactness and simplicity of integration. Further power and energy scaling in Nd:YAG [1] and Yb:YAG [2] single crystal fiber (SCF) chirped pulse amplifier (CPA) benefit from the pump guiding and improved heat removal. Compared with Nd:YAG, ytterbium-doped yttrium aluminium garnet (Yb:YAG) has significantly lower fractional heating [3].
We investigated Yb:YAG SCF seeded with 210 ps, 3.8 nm FWHM pulses of over 300 mW average power at 10 – 500 kHz repetition rates in a single and dual-end-pumped configuration. High brightness laser diodes of 50 W and 70 W power at 940 nm wavelength fiber-coupled into a 105 μm core provided the overall pump power of up to 120 W. We studied also a larger aperture Yb:YAG rods with unguided pump propagation of up to 140 W at 940 nm and 100 W at 969 nm wavelength. The main goal of our investigation was to optimize the first cascade of pumping source for 1 TW class optical parametric chirped pulse amplification (OPCPA).
The seed source was based on all-in-fiber passively mode-locked oscillator generating spectrally broadened to 3.8 nm and temporally stretched to ~ 0.2 ns pulses at 1030 nm wavelength. An acousto-optic modulator was used as a pulse picker to control pulse repetition rate in the range of 10 – 500 kHz. These pulses were further amplified up to ~ 500 mW of average power in Yb-doped fiber. Maximum pulse energy was limited to 14 μJ at 21 kHz repetition rate by nonlinear phase distortion in the amplifier.
Collimated seed beam of ~ 0.4 mm diameter was directed to SCF: Ø 1 × 40 mm, 1 % at. or larger aperture Yb:YAG rods: 5 × 5 × 5 mm3 5 % at., 5 × 5 × 20 mm3 and 2 × 2 × 20 mm3 2 % at. bonded to the water-cooled copper heat sink set at 15°C. Single or two fiber coupled laser diodes formed the waist of ~ 0.42 mm diameter at ~ 4 ÷ 5 mm depth inside the crystal. Faraday isolators were used for seed source protection and for decoupling the 2nd pass of amplified output. Induced thermal lens was compensated by tuning the distance between the spherical mirror and laser rod.

Yb:YAG CPA based on 2 × 2 × 20 mm3 rod doped 2% at. surpass the commercially available Yb:YAG SCF in terms of gain and optical-to-optical conversion efficiency while ensures nearly the same output beam quality with low spherical aberration. We achieved the amplified output of up to ~ 30 W in SCF with optical-to-optical efficiency of ~ 27 % and up to ~ 50 W (Fig.1 – left) in the larger aperture rod with ~ 38 % efficiency both featuring a beam quality of M2 ~ 1.1. The output pulses of ~ 3.5 mJ energy were attained from Yb:YAG rod at 10 kHz repetition rate. The same CPA pumped with ~ 87 W at 969 nm wavelength ensures ~ 19 W output with ~ 21% optical-to-optical efficiency and M2 ~ 1.06.
Despite the gain narrowing to ~ 1.8 nm, we obtained ~ 600 fs pulses (Fig.1 – right) with power conversion efficiency of 80 % using compressor based on diffraction grating with 1700 grooves/mm.
Unsurpassed double-pass gain of up to ~ 42 dB, amplified beam quality M2 ~ 1.1, low cost and alignment simplicity makes the 2 × 2 × 20 mm3 2% at. Yb:YAG rod the excellent choice for high average output power and energy CPA under pump levels below 140 W.