COMPACT YB:YAG CPA SYSTEM WITH ALL-IN-FIBER SEED SOURCE

Laurynas Veselis1, 2, Tadas Bartulevičius1, 2, Aleksej Rodin1, 2, Nerijus Rusteika1, 2

1 Solid State Laser Laboratory, department of Laser Technologies, Center for Physical Sciences and Technology, Savanoriu 231, LT-02300 Vilnius, Lithuania

2 UAB Ekspla, Savanoriu 237, LT-02300 Vilnius, Lithuania

All-in-fiber seed sources are irreplaceable in laser systems where beam quality, compactness and ease of integration is necessary. However, all-in-fiber laser systems face a challenge handling nonlinearity accumulated in fibers and fiber amplifiers, limiting output energy in 100's µJ level and average power in 100 W level, with pulse durations <1 ps at central wavelength of 1030 nm [1-2]. Although there are demonstrations of energy scaling using all-in-fiber systems to >1 mJ and average power of 1 kW at 100 kHz repetition rate and pulse duration <1 ps, but an Yb-doped, ultra large-core, single-mode photonic crystal fiber (PCF) rod was used for last amplification stage [3]. In this case the term “all-in-fiber” is debatable, as rod itself is large and rigid. Also the compactness of the system suffers.

In this work a hybrid approach of chirped pulse amplification (CPA) system was studied using all-in-fiber seed source and Yb:YAG crystal as a last amplification stage [4-5]. Setup was seeded with ~200 ps pulse duration, 500mW average power pulses at 11 MHz repetition rate. Single end-pumped configuration with 70W high-brightness laser diode at 940 nm coupled into a 105 µm fiber core (NA = 0.15) was used (Fig. 1.). Both seed and pump beams were focused to ~0.4 mm beam width at 1/e2 level. 2x2x20 mm Yb:YAG crystal doped 2 at. % Yb was used for experiments. Both crystal and pump diode were water chilled (seperately). Single and double pass setup was studied.

Figure 1
Fig. 1. Experimental setup of single-end pumped double pass Yb:YAG CPA system with all-in-fiber seed source.

Amplified output of 5 W in a single pass and 12 W in double-pass CPA has been achieved at 11 MHz repetition rate, with M2<1.1 after double-pass. Simulation of amplification was also demonstrated and showed a good agreement with experimental results. More experimental and simulation results will be presented at the conference.


[1] Z. Liu, L. Shah, I. Hartl, G. C. Cho, and M. E. Fermann, High-energy fiber chirped-pulse amplification system based on cubicons, Proceedings of the Conference on Lasers and Electro-Optics (Baltimore, 2005).

[2] A. Galvanauskas, Mode-scalable, fiber-based, chirped-pulse amplification systems, IEEE J. Sel. Top. Quantum Electron. 7 (4), 504–517 (2001).

[3] P. Wan, L. M. Yang, J. Liu, All fiber-based Yb-doped high energy, high power femtosecond fiber lasers, Opt. Express, 21 (24), 29854-9 (2013).

[4] A. M. Rodin, A. Aleknavicius, A. Michailovas, and A. S. Dementjev, Beam quality investigation in Nd:YAG crystal fiber amplifier pumped at > 110 W, Proc. SPIE, 9342, 934207-16 (2015).

[5] X. Délen, Y. Zaouter, I. Martial, N. Aubry, J. Didierjean, C. Hönninger, E. Mottay, F. Balembois, and P. Georges, Yb:YAG single crystal fiber power amplifier for femtosecond sources, Optics Letters, 38 (2), 109 – 111 (2013).